Fishers exterior trim

Ryan and I finished another large exterior trim job in Fishers. The house had not been painted for 11 years. It included all the wood trim, shutters, gutters, front steel door, and 3-car garage doors. It took us five days, which included pressure washing, prepping, and applying the finish coat.  We worked until 7:30 p.m. the last day to finish up.

Details of the project:

• We pressure washed all the wood trim and also the siding that was dirty. It wasn't part of the estimate but it doesn't take much longer to hit the siding;
• We applied 11 or 12 tubes of both white and clear caulk. They had a lot of brick on the front so we removed all the failing caulk and replaced with clear caulk around the brick;
• We scraped any failing paint that the pressure washing did not remove;
• Applied four gallons of Sherwin Williams Exterior Duration paint in a satin finish (Summer White) on the soffits, overhang, fascia boards, 3-car garage doors, man-door, and gutters;
• Applied Sherwin Williams Exterior SuperPaint in a satin finish (Tricorn Black) to the shutters, planters, and front steel door; and
• We sprayed both the 3-car garage doors and the front steel door and used a mini-roller (1/2 nap) and a brush for the rest.

Challenges:

• We had to use our steel deck boots on one of the high peaks that was very steep in order to reach the overhang. You can see the high peaks on the first photo. We had to use our 32 foot extension ladder to reach the highest peak and also to step onto the lower peak to get to the overhang. As mentioned, we used a deck boot (http://www.provisiontools.com/roofboot.asp) and Pivit ladder tool (http://www.provisiontools.com/pivit.asp) to stand on the steep roof line;
• We had to apply two coats of the Tricorn Black to the shutters because they were not covering the green color in one coat;
• Our small sprayer would not work with the Tricorn Black because it was too thick even after thinning.  We eventually broke out the large sprayer again to spray the front door;
• A lot of the corner boards on the wood trim were cracked or had large gaps. We had to re-nail and apply caulk before painting; and
• We had rain on two of the days so had to work around the rain. Also, it was very cool and cloudy the last day so the front door did not dry as fast as we liked.

Photos:

Carmel repaint

We received a call from a client where we had completed an interior painting project several weeks ago.  There were two rooms that the customer did not like the color so she asked us to repaint two of the rooms - a large living room, entryway, and hallway.  The original color had some blue in it and they really wanted more of a gray to match their furniture and rugs. The final color was Sherwin Williams "Mindful Gray." Take a look.

 Below is the original color in the same room.

Fishers residential exterior trim

We just completed a large Fishers house that included all the wood trim, large front porch, and shutters. We used Sherwin Williams Duration exterior in a satin finish on the wood and a Lowes Valspar satin (midnight green) on the shutters.

Ryan was on vacation most of this job so missed all the prep. I first pressure washed all the wood trim and front porch. Then I spent almost an entire day prepping the wood that included scraping and a lot of  caulking (5 tubes.) The porch posts were in need of a lot of repair and I probably spent 3 hours on them alone.

There were some difficult areas to get to because of the height and roof lines. The front of the house had peaks over the front porch so had to use several ladders to get to the peaks. The south side of the house had a peak over the garage that we used special ladders to reach. It took us a while to figure how we were going to reach the overhang. Look at the photos and you will see what we had to do.

The thick "Duration" paint really filled in a lot of the rough cedar and looked great in the satin finish.  The shutters were really faded and the Valspar satin paint made them look almost brand new.

Three decks in three days

Ryan & I finished our third deck in three (3) days. We used Sherwin Williams Deckscape waterborne stain in a solid color we matched to the previous color. Compared to the last deck we completed, this was a piece of cake.

Steps in completing:

1. Pressure washed deck using a deck cleaner one week before we stained;
2. Washed the deck floor with a Sherwin Williams Deckscape deck wash two days before we stained;
3. Checked the moisture in the railing, spindles, and floor before applying any stain. It was 6%, which is well below the 10% we are looking for;
4. Sprayed the railing and spindles first and then back brushed to penetrate and avoid any drips; and
5. Sprayed the floor and then back brushed to penetrate the floor.

Challenges:

1. There were rose bushes and other bushes around the outside of the deck that made it difficult to get to all areas.
2. Working around rain made it very tough to get moisture levels below 10%.

Fishers stained deck - oil base

Ryan and I finished another deck on Tuesday. We used an oil base stain for the first time - normally we use waterborne stain. Oil base actually is better for decks but it is more difficult to work with, and also is high in VOC and odor. We also have to clean our sprayer with mineral spirits, which is different than cleaning with water.

A key to using oil base is to ensure less than 10% moisture in the wood. As we know water and oil do not mix. Also, there should not be any rain in the forecast for 24 to 48 hours.  It will take that long to dry to touch.  It may still be a little tacky.

Steps we took to complete this deck.

1. Pressure washed and cleaned the deck a week ago. This included digging out the bottom of the deck to ensure we could stain to prevent rotting (2 hours);
2. Washed the deck again on Monday with a Sherwin Williams Deckscape deck wash to ensure the deck was as clean as we could get it  (2 hours);
3. Purchased 4 gallons of Sherwin Williams Deckscape semi-transparent stain in "Hawthorne" color. We used almost all of it. When you sprain spindles, you get about 100 square feet (lose a lot to the air since you are not hitting surface all the time) per gallon and when you spray the floor, you get 200-250 square feet per gallon (2 hours);
4. Sprayed and back brushed the spindles and benches (2 hours); and
5. Sprayed and back brushed the floors (2 hours). 

Notes:
- Always wear a mask and protective glasses with oil base;
- Ensure you back brush all areas or you will get puddling, and it will not penetrate the wood as well;
- Do not get any stain on grass or flowers. The oil base will damage or kill any plants and grass; and
- All photos taken with my iPhone 4S.

Fishers large deck and Pergola - Completion

Ryan and I sprayed out the skirting and the 3 deck floors (800 square feet) on Sunday and only have a few minor touch-ups before completion. This project was definitely a challenge and our largest deck attempted.

The customer chose a two toned deck with the pergola, railing, and spindles (175) stained in a "Stonington Beige" color. We used 8 gallons. The color was chosen to match their trim. We brushed out the pergola for two reasons - 1) it was very windy; and 2) you just lose to much stain in large open areas like a pergola. We sprayed the railing and spindles.  Even though you lose a lot of stain due to the open areas doing spindles, it just takes too much time to brush the 175 spindles and spraying does a better job with all the little areas hard to reach with a brush.

The customer chose "Cordovan Brown" for the three deck floors. We used six gallons of stain. Ryan laid on the stain with our sprayer and I back brushed with a 4 inch stain brush.  We took two boards at a time because it was warm out and we did not want any lap marks. It took us only 3 hours to completely stain the decks.We had some over spray onto the other color, but it was easy to go back and touch-up.

These are the steps we followed to tackle a job like this:

1. Cleared the deck of all furniture. This included a heavy fire pit and grill;
2. Sprayed on a deck cleaner on and let it soak in;
3. Pressure washed the deck with our 3,100 PSI machine being careful not to tear up the wood;
4. We let the deck dry for one day and always measured for moisture to ensure the wood was dry;
5. Stained the pergola and lathes on top. We put 2 coats on because of the lighter color and brushing;
6. Stained and back brushed the railing and spindles;
7. Stained and back brushed the skirting;
8. Applied a Deckscape deck wash to get the floor absolutely clean. We did not go on the deck floor again with dirty shoes.
9. Stained the deck floors when the moisture level finally got less than 12%.

Challenges:

1. Wind
2. Moisture
3. Rain
4. Masking certain areas

Golf course deck prep

Ryan and I prepped and are now staining a large 800 square foot deck floor along with railing, spindles, and steps. And throw in a pergola on top of it and you have a large staining project.  The deck is on a golf course and will look spectacular when done because of the colors chosen by the customer.  They are going with a two toned look with the pergola, spindles, and railing the color of the house trim and the deck floor a dark brown.  I am excited to see the final product.